"Unable to read toc-file"

Post by **Mark Arends** » Sun Jul 15, 2007 12:50 pm

If you get the error "Unable to read toc-file" when installing NL2000 version 3.0 please try:

guido wrote:As for now it seems to have something to do with the .NET framework on these machines. Try uninstalling .NET framework 1.1 and installing 2.0 afterwards. That solved the problem for a few users.

Philipp · Post by **Philipp** » Tue Jul 24, 2007 8:53 pm

Hi,

first I would like to thank you for this outstanding scenery. Well done!

I have got the upper mentioned problems during installation,

I am running Win Vista 32-bit. I deleted Version 1.1 of .Net after I heard about this problem.

.Net V2 is allready included in Win Vista. Then I wanted to install again but the same problem appeared on and on.

So I installed V3 of .Net but nothing changed.

I don't know what I can do anymore?

Is there any opportunity to delete .Net V2 and V3 cleanly from Win Vista, for a clean reinstallation?

Or do you have any other advice for me ?

Thanks a lot.

Philipp

wolf32 · Post by **wolf32** » Tue Jul 24, 2007 9:49 pm

Hi Phillip,

Wait before deleting .net of your PC, at the moment some more users experience this problem.
We are working on it, at this point it seems that the problem is causing by corrupt .toc files and/or a corrupt NL2000V3 file located on DVD1.
This can be caused by the download process or the burn on DVD process.
So first compare your contents of your dvd's like this list mentionent in the dutch forum (scroll a little down), keep in mind it will not says everything
http://www.nl-2000.com/nuke/modules.php ... 9&start=15
If you don't trust your toc files wich you can open with notepad and should end with "end" than you have to download them again or if it's caused by the burning process you've to try to burn dvd1 again.
Kind regards

wolf32 · Post by **wolf32** » Wed Jul 25, 2007 8:50 am

Just to keep you informed.
A dutch user told us that his contents check of his DVD's seems correct like on the list, the amount of total files and filesizes were the same.
Strangely when he opened one of his .toc file with notepad located on dvd1 it was totaly empty but the filezise was ok.
So he decided to download dvd1 again with bittorent instead of the http download method.
Now it works fine he reported us at the dutch forum, so in his case his dvd1 seems ok but unfortunally it was incomplete.
So perhaps this information is also usefull for you.

Philipp · Post by **Philipp** » Sat Jul 28, 2007 2:31 pm

Hi,

thanks for your answer.

I downloaded CD No.1 again and now it works.

Thanks for your help!

I am useing dozens of photosceneries in FS2004. And after my first take off at EHAM with your new scenery I can say that the one by NL2000 is one of the very best I have ever seen.

Thank you very very much!!!

Philipp

rebo · Post by **rebo** » Fri Sep 07, 2007 6:03 pm

Hi,

I downloaded DVD1 again and I tried to reinstall .NET framework but nothing has changed. What else can I try?

It would be too bad if I can't use your great scenery!

Thanks in advance for your help!

Max

bku · Post by **bku** » Fri Sep 07, 2007 7:56 pm

What exactly is the error message you get?

Bert Kuyper

rebo · Post by **rebo** » Fri Sep 07, 2007 8:16 pm

After I accept the Copyright Notice I get this error message:

Installer is unable to read toc-file.
Please run the installer from NL2000 V3 DVD 1.

wolf32 · Post by **wolf32** » Sat Sep 08, 2007 9:45 am

This is more a step by step procedure, but first of all I recomend you to check the contents of your download, which can be check with the ISO files.
I don't know if you did the bittorent download procedure, otherwise you can download the ISO file 1 or even better all 5 ISO files with Firefox2 at Eweka, you can find the files at our startpage.
After that you can check the contents of you ISO files by a checksum program which is here to find
http://www.nl-2000.com/nuke/modules.php ... ic&p=10545
So than you know for sure if the contents of your download are ok.
Greetz

rebo · Post by **rebo** » Wed Sep 12, 2007 4:06 pm

First of all thanks for the fast replies!

I downloaded all 5 ISO files and checked them. They are all okay.

wolf32 · Post by **wolf32** » Wed Sep 12, 2007 7:42 pm

Ok, than we can count that out.
Did you try to install it from dvd disk, otherwise you can try to do an installation from Hard drive directly.
(tip for burning on dvd, do not burn at a high burnspeed)
Put both files nl2000v3.exe and vb6stkit.dll in a seperate folder on your harddrive for example temp and try to startup the installation from that folder by clicking nl2000v3.exe when asking to the .toc files redirect to the dvd then or to the location on your harddrive where you located the dvd files on your harddrive.

rebo · Post by **rebo** » Fri Sep 14, 2007 2:47 pm

Now I tried to install it from harddrive, I seperated the both files from the other files and I tried it from the DVD. But always the same error message...

wolf32 · Post by **wolf32** » Fri Sep 14, 2007 3:55 pm

Than it's probably .net problem some computers experience some problems with that, unfortunaly there is not a solution to that then just to try to uninstall .net 1.1 and afterwards install .net 2.0 or even 3.0.
You can try different (mixed) configurations in this but it's not sure that's the answer for some users it was for some not.
Here you can find the links to .net versions
http://www.nl-2000.com/nuke/modules.php ... pic&t=1852

wolf32 · Post by **wolf32** » Sat Sep 15, 2007 8:51 am

Here some more tips and tricks.
you can download a seperate installer file here wich works with .NET 2.0
http://www.nl-2000.com/nuke/modules.php ... c&start=15

When you do an installation disable your antivirus software.
For some people it works to do an installation in "safe mode"

rebo · Post by **rebo** » Sun Sep 16, 2007 12:06 pm

I tried it with the .net 2.0 installer and it worked, but then I saw that I need a few more GB's to install it. So I closed the installer and after I had enough space, I opened the installer again but then I got an error message from windows. After that I tried once again to uninstall .net 1.1 and installed .net 2.0. But it didn't work anymore, even after some reboots! Some hours later I tried it once more and suddenly it worked again!

Anyway thank you for your great support and the outstanding scenery!

Max

"Unable to read toc-file"

"Unable to read toc-file"

Who is online

Feed

Go to page